Skip to Content Information Center
Lexmark MX822

Lexmark MX822

Markvision Enterprise: Printer Not Communicating on the Network; Preliminary Wired or Wireless Network Troubleshooting



What you will see

You may observe one of the following network-related situations:

  • When attempting to print, you receive a Communication Not Available message or

  • -Document Failed to Print message or

  • -no message or

  • any other communication-related error message or

  • no printer or MFP response.

Where to begin

It is important to differentiate between communication failure and print failure.



you are not sure that the printer is communicating over the network

see the Network Communication Diagnosis topics below.

you have confirmed network connectivity


for an article that describes driver, port, and port-related topics.

you require additional assistance with the


in this article

consider other help options, including contacting

Lexmark Technical Support


Index of troubleshooting subjects covered here

  • Preliminary Communication Tests:
    • Network Settings Page - Status of Connected or Not Connected

    • Ping test
    • Embedded Web Server (EWS) access

    • Telnet: An additional communication test may help identify TCP/IP port closure in the 9000 range.

    • FTP Test: Print file (.prn; .ps; .pdf; or.xps file extensions)

  • Other factors that may prevent network communication:
    • TCP/IP port access
    • Restricted Server List
    • Speed and Duplex settings
    • Hardware Failure: Network Card Errors
  • Wireless* Topics:
    • W

      ireless Signal Strength

      • Multipath or RF Interference
      • MAC Filtering on the Router
    • N only mode

*Printers and MFPs equipped with Wireless (IEEE 802.11b/g/n) option cards.

Network Communication Diagnosis:

Before you begin:

  • It is recommended that you first perform the 'preliminary tests'.

  • Make sure the ethernet cable is fully seated into the RJ45 ethernet port on the back of the printer.

  • Confirm that the network cable is not damaged.

  • Confirm that the network cable connector is not damaged.

  • Confirm that the link LED is illuminated. If not, change the network cable or try a different access port on the switch, router, wall or hub.

  • If connected to the network using the 802.11b/g/n wireless network adapter, verify that other wireless clients are communicating on the same network or SSID.

  • Confirm that the printer is not displaying a 97x or 54 Std. or Network 1 error code. If it is, please contact

    Lexmark Technical Support


Advanced users should answer the following questions:

  • Does the network cable length conform specification for the type of network serviced?

  • Does the network signal suffer attenuation or signal loss?

  • Does this communication problem occur during peak hours? Oversaturation of network traffic is a possibility.

  • Is the switch access port forced to a specific speed and duplex speed, such as 10 Mbps half duplex?


Autonegotiate (AutoN) requires that both devices be set to auto.

I. Preliminary Communication Tests

Topic 1: Network Settings Page "Status"

Print the network settings page for your printer and check the Status value.Please reference the User Guide for instructions that can be found on the driver CD, or visit

Lexmark Publications

to download the latest version.

If the Status value displays...

Then...And then...

continue your diagnosis with

Topic 2

and the remaining topics as necessary.

go back to the top of the article and consider the Where to begin suggestions again.

Not Connected

see Before you begin just above this table and start your diagnosis at

Topic 8.

connect the printer to a known working network cable or network access port.

Topic 2: Ping test


to view instructions.

Topic 3: Printer web page access

  1. Open a web browser session to access it.

  2. Type



    where printer_IP_address is the TCP/IP address of the printer or MFP. This value is located on the network settings page located under TCP/IP.

  3. Verify that you can access different sections of the printer or print server's embedded web server.

Topic 4: Telnet test


to view instructions.

Topic 5: Send print file via FTP


for sample instructions.


The article title in the sample references the Lexmark C500n, but the procedure is almost identical for all printers.

II. Other factors that may prevent network printer/MFP funtion or communication

Topic 6:PrinterTCP/IP Port Access

Printers and MFPs require specific TCP/IP port numbers for certain network-related product features. For example, telnet requires port 9000.


  1. Access the printer web page (embedded web server).

  2. Click on Links and Index.

  3. Click on TCP/IP Port Access.

  4. Enable ports if necessary.

  5. Click Submit.

Click here

for illustration.

Topic 7:Restricted Server List

The Restricted Server List limits network printer access to clients whose IP addresses are entered into it (up to 10 clients are possible). One address entered into this list is all that is required to deny printer network communication to an an entire workgroup.


  1. Try to find the IP address causing the issue by opening a web browser session. To do this, type


    , where printer_IP_address is the TCP/IP address of the printer or MFP.

    Repeat this procedure from multiple clients if necessary.

  2. Identify this client machine's TCP/IP address.

    Click on Settings > Network/Ports > TCP/IP > Restricted Server List. Remove the IP address and click Submit. If you are unable to identify this address, please contact

    Lexmark Technical Support

    for possible alternative solutions.

CONFIGURATION NOTE: RSL can also be configured from a telnet session, UNC, or MVP device policy with products released after 2003.

Click here

for an image illustrating configuration methods.

Topic 8: Network Speed and Duplex Settings

Inconsistent or absent network communication can arise if autonegotiate (AutoN) is turned off or forced to a specific speed on a switch. This setting for network speed and duplex setting can even be configured for an individual network access port. The printer default setting is Auto. If inconsistent network communication is a problem, please contact

Lexmark Technical Support


NOTE: This setting is found in the printer's SE Menu under MAC > Set Card Speed for those network administrators who know how to access this menu.

Topic 9:Network Card Hardware Error

Again,confirm that the printer is not displaying a 976, 977 or 54 Std. or 54Network # error code.

Suggestion: Power the printer off and on. If the error persists, please contact

Lexmark Technical Support


III. Wireless Topics

Topic 10:Wireless Signal Strength Issue

Variables affecting wireless signal strength which may affect the ability to print include:

  • Distance between wireless router/access point and MarkNet print server.

  • Obstructions causing decreased signal strength. See

    Topic 8.

  • Other electronic devices and neighboring wireless networks which emit radio frequency (RF), e.g. microwaves, cordless phones, baby monitors.

  • Obstructive placement of the print server, e.g. behind or underneath furniture.

What to do

  • Print the network settings page and observe the Bitrate value. Lower values indicate a weaker signal, leading to a greater likelihood of print server failure or a reduction in performance.

    Data Rate Selection Values:

    1,2,5.5,11 Mbps

    6,9, 12,15,24,36,48,54 Mbps

  • Reposition the access point.

  • Reposition the print server antenna.

  • Temporarily turn off other devices that emit RF.

  • Adjust access point antennas.

  • Consider the purchase of high-gain antennas for the router.

  • Consider the purchase of a wireless repeater or range extender.

  • Reposition possible obstructions.

  • Find out if the router supports a radio power throttling and if a more powerful radio setting is available.

  • See

    Topic 12

    for additional suggestions.

Topic 11: Authentication and Association

Below is a brief overview of some possible scenarios that may occur after successful configuration (authentication and association) between the printer's wireless (80211b/g/n) print server and the wireless router or access point. These possibilities may include any of the following:

    • The printer's wireless network adapter has not completed the process of authenticating or associating with the wireless router's AP. Suggestion: Wait for a moment to see is this process completes.


      You may have to run the Wireless Setup Utility to re-establish communication with the wireless router/AP.

    • A change to Draft-N only mode running in 5GHz only mode. Suggestion: Lexmark wireless adapters support Draft-N in the 2.4Ghz band only.See the router documentation or embedded web server for more information.

    • The printer is associating with the wrong network or network name (SSID). Suggestion: Make sure neighboring networks are not utilizing the same network name (SSID).

    • An Auto IP address of 169.254.#.# indicates that we authenticated with the AP, but the wireless print server was unable to obtain a DHCP administered address from the router. Wait for a moment, rerun the Wireless Setup Utility if necessary, or check the router's DHCP settings to verify that the router is running in router mode.

    • A security certificate issue. See your network administrator if the extensible authentication protocol (EAP) is being implemented. (This is also known as WPA2 Enterprise security.)

    • Make sure you can ping the router's IP address or the IP gateway.

Topic 12: Multipath or RF Interference Issue

All forms of multipath and RF interference can affect the success of a wireless print request.

Examples of multipath obstructions:

    • Reflection - e.g. the earth's surface, buildings, walls, mirrors, shiny metal surfaces

    • Refraction - e.g. cold air, a glass pane

    • Scattering - e.g. any rough surface causing multiple reflections or scattering of RF waves.

    • RF Shadow - e.g. space behind point or points of diffraction that cause dead space. The print server will not work in these areas.

    • Diffraction - e.g. the bending of RF waves around an obstruction, such as a door.

    • Absorption - e.g. air, water, plants, animals, concrete See below for an illustration. If additional explanations of these terms are needed, click


      for a Glossary of Wireless Terms.

RF Interferenceexamples:

    • Microwave ovens

    • 2.4GHz spread spectrum cordless phones

    • Baby monitors

    • Sunlight

    • Elevators

    • Neighboring wireless networks

    • Any device that utilizes spread spectrum radio frequency.

What to do

Follow the suggestions in

Topic 10: Wireless Signal Strength.

  • Change the subchannel on your cordless phone if this feature is available. Alternatively, consider the purchase of a 5GHz+ range phone. Consult the Phone Owner's Guide for more information.

  • Change the channel on the wireless router/AP.

  • Consider the replacement of any device that creates all-band interference, such as microwave ovens.

  • Alter environmental conditions such as bright sunlight.

  • If applicable, reduce radio power in congested areas if the router has this reduction feature.

  • Raise radio power level if the router has this capability and the printer is suffering from low signal quality.

Topic 13: Other Issues

Other possible causes of printing failure include:

  • Firewall issues preventing communication

    • Make sure you always click


      when a


      process or similar process is required.

    • Obtain a list of ports and affiliated processes that Lexmark printers or MFPs utilize.

    • Check to remove the application quarantine or blocked list within the the firewall application.

  • Workplace


    (Virtual Private Networks) are preventing communication

    Suggestion: VPN tunneling may be required for successful communication to the printer.

  • MAC filtering may have been initiated on the router.


    Obtain the printer's MAC (UAA) address from the network settings page, and then verify that this value is entered into the MAC inclusions or ALLOW list within the router's configuration utility, web page, or other.

  • Document formatting

  • Driver settings

  • Application-specific issues relating to the application's Printer Setup

  • USB connection problem if locally attached to a PC or Mac

  • Firewall issues preventing communication

Topic 14: Last Resort Solution

  • If you have tried all of the above suggestions without resolving the issue, reboot your computer and try printing again.

  • If the issue persists, try resetting the printer's network adapter and reconfiguring the printer using the Wireless Setup Utility.

  • Note:

    You will need to connect the print server via USB cable to the client or host computer and you will need to know the network name (SSID) of your network, the encryption method, and the security/network key or passphrase.

Related Articles:

  • xref_SO4663_xref

Still Need Help?

Have the following available when calling Lexmark Technical Support;

  • Printer model(s)

  • Printer serial number


Je bil ta članek koristen?