PCL Emul menu

Font Source

• Resident
• Disk
• Download
• Flash
• All

Specify the set of fonts used by the Font Name menu.

Notes:

• “Resident” is the factory default setting. Resident shows the factory default set of fonts downloaded in the RAM.
• “Flash” and “Disk” settings show all fonts resident in that option.
• The flash option must be properly formatted and cannot be read/write‑, write‑, or password‑protected.
• “Download” shows all the fonts downloaded in the RAM.
• “All” shows all fonts available to any option.

Font Name

• Courier 10

Identify a specific font and the option where it is stored.

Note:  Courier 10 is the factory default setting. Courier 10 shows the font name, font ID, and the storage location in the printer. The font source abbreviation is R for Resident, F for Flash, K for Disk, and D for Download.

Symbol Set

• 10U PC‑8
• 12U PC‑850

Specify the symbol set for each font name.

Notes:

• 10U  PC‑8 is the US factory default setting. 12U  PC‑850 is the international factory default setting.
• A symbol set is a set of alphabetic and numeric characters, punctuation, and special symbols. Symbol sets support the different languages or specific programs such as math symbols for scientific text. Only the supported symbol sets are shown.

PCL Emulation Settings

• Point Size
• 1.00–1008.00

Change the point size for scalable typographic fonts.

Notes:

• 12 is the factory default setting.
• Point size refers to the height of the characters in the font. One point equals approximately 0.014 inch.
• Point sizes can be increased or decreased in 0.25‑point increments.

PCL Emulation Settings

• Pitch
• 0.08–100

Specify the font pitch for scalable monospaced fonts.

Notes:

• 10 is the factory default setting.
• Pitch refers to the number of fixed‑space characters per inch (cpi).
• Pitch can be increased or decreased in 0.01‑cpi increments.
• For nonscalable monospaced fonts, the pitch appears on the display but it cannot be changed.

PCL Emulation Settings

• Orientation
• Portrait
• Landscape

Specify the orientation of text and graphics on the page.

Notes:

• Portrait is the factory default setting. Portrait prints text and graphics parallel to the short edge of the page.
• Landscape prints text and graphics parallel to the long edge of the page.

PCL Emulation Settings

• Lines per Page
• 1–255

Specify the number of lines that print on each page.

Notes:

• 60 is the US factory default setting. 64 is the international default setting.
• The printer sets the amount of space between each line based on the Lines per Page, Paper Size, and Orientation settings. Select the Paper Size and Orientation you want before setting Lines per Page.

PCL Emulation Settings

• A4 Width
• 198  mm
• 203  mm

Set the printer to print on A4‑size paper.

Notes:

• “198  mm” is the factory default setting.
• The 203‑mm setting sets the width of the page to allow printing of eighty 10‑pitch characters.

PCL Emulation Settings

• Auto CR after LF
• On
• Off

Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.

Note:  Off is the factory default setting.

PCL Emulation Settings

• Auto LF after CR
• On
• Off

Specify whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command.

Note:  Off is the factory default setting.

Tray Renumber

• Assign MP Feeder
• Off
• None
• 0–199
• Assign Tray  [x]
• Off
• None
• 0–199
• Assign Manual Paper
• Off
• None
• 0–199
• Assign Manual Env
• Off
• None
• 0–199

Configure the printer to work with printer software or programs that use different source assignments for trays and feeders.

Notes:

• “Off” is the factory default setting.
• “None” ignores the Select Paper Feed command. This option appears only when it is selected by the PCL  5 interpreter.
• “0–199” allows a custom setting to be assigned.

Tray Renumber

• View Factory Defaults
• MPF Default = 8
• T1 Default = 1
• T1 Default = 4
• T1 Default = 5
• T1 Default = 20
• T1 Default = 21
• Env Default = 6
• MPaper Default = 2
• MEnv Default = 3

Display the factory default setting assigned to each tray or feeder.

Tray Renumber

• Restore Defaults
• Yes
• No

Restore all tray and feeder assignments to the factory default settings.